94 lines
2.7 KiB
C
94 lines
2.7 KiB
C
/* RTOS_TFLuna.c
|
|
* Jonathan Valvano
|
|
* Oct 22, 2025
|
|
* Remove 3.3V J101 jumper to run RTOS sensor board or motor board
|
|
* A two-pin female header is required on the LaunchPad TP10(XDS_VCC) and TP9(!RSTN)
|
|
*/
|
|
|
|
#include <ti/devices/msp/msp.h>
|
|
#include "../inc/LaunchPad.h"
|
|
#include "../inc/Clock.h"
|
|
#include "../RTOS_Labs_common/TFLuna1.h"
|
|
#include "../RTOS_Labs_common/TFLuna2.h"
|
|
#include "../RTOS_Labs_common/TFLuna3.h"
|
|
#include "../RTOS_Labs_common/SPI.h"
|
|
#include "../RTOS_Labs_common/ST7735_SDC.h"
|
|
#include <stdio.h>
|
|
/* RTOS sensor board supported three TF-Luna sensors
|
|
Serial TxD: PA17 is UART1 Tx (MSPM0 to TFLuna1)
|
|
Serial RxD: PA18 is UART1 Rx (TFLuna1 to MSPM0)
|
|
Serial TxD: PB17 is UART2 Tx (MSPM0 to TFLuna2)
|
|
Serial RxD: PB18 is UART2 Rx (TFLuna2 to MSPM0)
|
|
Serial TxD: PB12 is UART3 Tx (MSPM0 to TFLuna3), shared with LD19 Lidar
|
|
Serial RxD: PB13 is UART3 Rx (TFLuna3 to MSPM0)
|
|
UART3 is shared between LD19 and TFLuna3 (can have either but not both)
|
|
overhead of TFLuna will be 17us/measurement at 100 measurements/sec
|
|
*/
|
|
uint32_t Dist1,Dist2,Dist3;
|
|
uint32_t Count1,Count2,Count3;
|
|
void Background1(uint32_t d){
|
|
Dist1 = d;
|
|
Count1++;
|
|
}
|
|
void Background2(uint32_t d){
|
|
Dist2 = d;
|
|
Count2++;
|
|
}
|
|
void Background3(uint32_t d){
|
|
Dist3 = d;
|
|
Count3++;
|
|
}
|
|
int main(void){
|
|
__disable_irq();
|
|
Clock_Init80MHz(0); // no clock out to pin
|
|
LaunchPad_Init();
|
|
SPI1_Init();
|
|
ST7735_InitR(INITR_REDTAB); //INITR_REDTAB for AdaFruit, INITR_BLACKTAB for SPI HiLetgo ST7735R
|
|
ST7735_FillScreen(ST7735_BLACK);
|
|
ST7735_SetCursor(0, 0);
|
|
ST7735_OutString("TF Luna test\n");
|
|
ST7735_OutString("Dist1= \n");
|
|
ST7735_OutString("Dist2= \n");
|
|
ST7735_OutString("Dist3= \n");
|
|
TFLuna1_Init(&Background1);
|
|
TFLuna2_Init(&Background2);
|
|
TFLuna3_Init(&Background3);
|
|
Count1=Count2=Count3=0;
|
|
__enable_irq();
|
|
TFLuna1_Format_Standard_mm(); // format in mm
|
|
TFLuna1_Frame_Rate(); // 100 samples/sec
|
|
TFLuna1_SaveSettings(); // save format and rate
|
|
TFLuna1_System_Reset(); // start measurements
|
|
|
|
TFLuna2_Format_Standard_mm(); // format in mm
|
|
TFLuna2_Frame_Rate(); // 100 samples/sec
|
|
TFLuna2_SaveSettings(); // save format and rate
|
|
TFLuna2_System_Reset(); // start measurements
|
|
|
|
TFLuna3_Format_Standard_mm(); // format in mm
|
|
TFLuna3_Frame_Rate(); // 100 samples/sec
|
|
TFLuna3_SaveSettings(); // save format and rate
|
|
TFLuna3_System_Reset(); // start measurements
|
|
while(1){
|
|
if(Count1){
|
|
Count1 = 0;
|
|
ST7735_SetCursor(7, 1);
|
|
ST7735_OutUDec4(Dist1);
|
|
}
|
|
if(Count2){
|
|
Count2 = 0;
|
|
ST7735_SetCursor(7, 2);
|
|
ST7735_OutUDec4(Dist2);
|
|
}
|
|
if(Count3){
|
|
Count3 = 0;
|
|
ST7735_SetCursor(7, 3);
|
|
ST7735_OutUDec4(Dist3);
|
|
}
|
|
}
|
|
}
|
|
|
|
|
|
|
|
|