all
This commit is contained in:
280
inc/SPI.c
Normal file
280
inc/SPI.c
Normal file
@@ -0,0 +1,280 @@
|
||||
/* SPI.c
|
||||
* Jonathan Valvano
|
||||
* November 21, 2022
|
||||
* Derived from uart_rw_multibyte_fifo_poll_LP_MSPM0G3507_nortos_ticlang
|
||||
SPI MKII LCD
|
||||
J1.7 SPI1 SCLK PB9_SPI1-SCK
|
||||
J2.13 SPI1 CS0 PB6_SPI1-CS0
|
||||
J2.15 SPI1 PICO PB8_SPI1-PICO
|
||||
J2.17 LCD !RST PB15
|
||||
J4.31 LCD RS PB16
|
||||
*/
|
||||
|
||||
|
||||
#include <ti/devices/msp/msp.h>
|
||||
#include "../RTOS_Labs_common/SPI.h"
|
||||
#include "../inc/Clock.h"
|
||||
#include "../inc/Timer.h"
|
||||
#include "../inc/LaunchPad.h"
|
||||
|
||||
/*
|
||||
// calls Clock_Freq to get bus clock
|
||||
// initialize SPI for 8 MHz baud clock
|
||||
// busy-wait synchronization
|
||||
// SPI0,SPI1 in power domain PD1 SysClk equals bus CPU clock
|
||||
void SPI_Init(void){uint32_t busfreq = Clock_Freq();
|
||||
// assumes GPIOA and GPIOB are reset and powered previously
|
||||
// RSTCLR to SPI1 peripherals
|
||||
// bits 31-24 unlock key 0xB1
|
||||
// bit 1 is Clear reset sticky bit
|
||||
// bit 0 is reset gpio port
|
||||
SPI1->GPRCM.RSTCTL = 0xB1000003;
|
||||
// Enable power to SPI1 peripherals
|
||||
// PWREN
|
||||
// bits 31-24 unlock key 0x26
|
||||
// bit 0 is Enable Power
|
||||
SPI1->GPRCM.PWREN = 0x26000001;
|
||||
// configure PB9 PB6 PB8 as alternate SPI1 function
|
||||
IOMUX->SECCFG.PINCM[PB9INDEX] = 0x00000083; // SPI1 SCLK
|
||||
IOMUX->SECCFG.PINCM[PB6INDEX] = 0x00000083; // SPI1 CS0
|
||||
IOMUX->SECCFG.PINCM[PB8INDEX] = 0x00000083; // SPI1 PICO
|
||||
IOMUX->SECCFG.PINCM[PB15INDEX] = 0x00000081; // GPIO output, LCD !RST
|
||||
IOMUX->SECCFG.PINCM[PB16INDEX] = 0x00000081; // GPIO output, LCD RS
|
||||
// ** IOMUX->SECCFG.PINCM[PA13INDEX] = 0x00000081; // GPIO output, LCD RS
|
||||
Clock_Delay(24); // time for gpio to power up
|
||||
// ** GPIOA->DOE31_0 |= 1<<13; // PA13 is LCD RS
|
||||
GPIOB->DOE31_0 |= 1<<16; // PA13 is LCD RS
|
||||
GPIOB->DOE31_0 |= 1<<15; // PB15 is LCD !RST
|
||||
GPIOB->DOUTSET31_0 = 1<<16; // RS=1
|
||||
// ** GPIOA->DOUTSET31_0 = 1<<13; // RS=1
|
||||
GPIOB->DOUTSET31_0 = 1<<15; // !RST = 1
|
||||
SPI1->CLKSEL = 8; // SYSCLK
|
||||
// bit 3 SYSCLK
|
||||
// bit 2 MFCLK
|
||||
// bit 1 LFCLK
|
||||
SPI1->CLKDIV = 0; // divide by 1
|
||||
// bits 2-0 n (0 to 7), divide by n+1
|
||||
//Set the bit rate clock divider to generate the serial output clock
|
||||
// outputBitRate = (spiInputClock) / ((1 + SCR) * 2)
|
||||
// 8,000,000 = (16,000,000)/((0 + 1) * 2)
|
||||
// 8,000,000 = (32,000,000)/((1 + 1) * 2)
|
||||
// 6,666,667 = (40,000,000)/((2 + 1) * 2)
|
||||
// 10,000,000 = (40,000,000)/((1 + 1) * 2)
|
||||
// 8,000,000 = (80,000,000)/((4 + 1) * 2)
|
||||
// 8,000,000 = (Clock_Freq)/((m + 1) * 2)
|
||||
// m = (Clock_Freq/16000000) - 1
|
||||
if(busfreq <= 16000000){
|
||||
SPI1->CLKCTL = 0; // frequency= busfreq/2
|
||||
}else if(busfreq == 40000000){
|
||||
SPI1->CLKCTL = 1; // frequency= 10MHz
|
||||
// SPI1->CLKCTL = 2; // frequency= 6.66MHz
|
||||
}else{
|
||||
SPI1->CLKCTL = busfreq/16000000 -1; // 8 MHz
|
||||
}
|
||||
SPI1->CTL0 = 0x0027;
|
||||
// bit 14 CSCLR=0 not cleared
|
||||
// bits 13-12 CSSEL=0 CS0
|
||||
// bit 9 SPH = 0
|
||||
// bit 8 SPO = 0
|
||||
// bits 6-5 FRF = 01 (4 wire)
|
||||
// bits 4-0 n=7, data size is n+1 (8bit data)
|
||||
SPI1->CTL1 = 0x0015;
|
||||
// bits 29-24 RXTIMEOUT=0
|
||||
// bits 23-16 REPEATX=0 disabled
|
||||
// bits 15-12 CDMODE=0 manual
|
||||
// bit 11 CDENABLE=0 CS3
|
||||
// bit 7-5 =0 no parity
|
||||
// bit 4=1 MSB first
|
||||
// bit 3=0 POD (not used, not peripheral)
|
||||
// bit 2=1 CP controller mode
|
||||
// bit 1=0 LBM disable loop back
|
||||
// bit 0=1 enable SPI
|
||||
SPI_Reset();
|
||||
}
|
||||
|
||||
|
||||
//---------SPI_OutData------------
|
||||
// Output 8-bit data to SPI port
|
||||
// Input: data is an 8-bit data to be transferred
|
||||
// Output: none
|
||||
void SPI_OutData(char data){
|
||||
while((SPI1->STAT&0x02) == 0x00){}; // spin if TxFifo full
|
||||
GPIOA->DOUTSET31_0 = 1<<13; // RS=PA13=1 for data
|
||||
SPI1->TXDATA = data;
|
||||
}
|
||||
//---------SPI_OutCommand------------
|
||||
// Output 8-bit command to SPI port
|
||||
// Input: data is an 8-bit data to be transferred
|
||||
// Output: none
|
||||
void SPI_OutCommand(char command){
|
||||
while((SPI1->STAT&0x10) == 0x10){}; // spin if SPI busy
|
||||
GPIOA->DOUTCLR31_0 = 1<<13; // RS=PA13=0 for command
|
||||
SPI1->TXDATA = command;
|
||||
while((SPI1->STAT&0x10) == 0x10){}; // spin if SPI busy
|
||||
}
|
||||
*/
|
||||
|
||||
//---------SPI1_Reset------------
|
||||
// Reset LCD
|
||||
// Input: none
|
||||
// Output: none
|
||||
// at 48 MHz
|
||||
void SPI1_Reset(void){
|
||||
// GPIOB->DOUTSET31_0 = 1<<15; // PB15=!RST=1
|
||||
TFT_RST_HIGH();
|
||||
Clock_Delay1ms(500); // 500ms (calibrated with logic analyzer)
|
||||
//GPIOB->DOUTCLR31_0 = 1<<15; // PB15=!RST=0
|
||||
TFT_RST_LOW();
|
||||
Clock_Delay1ms(500); // 500ms
|
||||
//GPIOB->DOUTSET31_0 = 1<<15; // PB15=!RST=1
|
||||
TFT_RST_HIGH();
|
||||
Clock_Delay1ms(500); // 500ms
|
||||
}
|
||||
|
||||
//********SPI1_Init*****************
|
||||
// Initialize SPI1 interface to SDC and TFT
|
||||
// inputs: none
|
||||
// outputs: none
|
||||
// outputBitRate = (spiInputClock) / ((1 + SCR) * 2)
|
||||
// 99 for 400,000 bps slow mode, used during initialization
|
||||
// 4 for 8,000,000 bps fast mode, used during disk I/O
|
||||
// Version for both SDC and TFT
|
||||
int LCDresetFlag;
|
||||
void SPI1_Init(void){
|
||||
TimerG0_IntArm(1000,40,1); // initialize TimerG0 for 1 ms interrupts
|
||||
CS_Init(); // initialize whichever GPIO pin is CS for the SD card
|
||||
uint32_t busfreq = Clock_Freq();
|
||||
// assumes GPIOA and GPIOB are reset and powered previously
|
||||
// RSTCLR to SPI1 peripherals
|
||||
// bits 31-24 unlock key 0xB1
|
||||
// bit 1 is Clear reset sticky bit
|
||||
// bit 0 is reset gpio port
|
||||
SPI1->GPRCM.RSTCTL = 0xB1000003;
|
||||
// Enable power to SPI1 peripherals
|
||||
// PWREN
|
||||
// bits 31-24 unlock key 0x26
|
||||
// bit 0 is Enable Power
|
||||
SPI1->GPRCM.PWREN = 0x26000001;
|
||||
// configure PB9 PB6 PB8 as alternate SPI1 function
|
||||
IOMUX->SECCFG.PINCM[PB9INDEX] = 0x00000083; // SPI1 SCLK
|
||||
// IOMUX->SECCFG.PINCM[PB6INDEX] = 0x00000083; // SPI1 CS0
|
||||
IOMUX->SECCFG.PINCM[PB8INDEX] = 0x00000083; // SPI1 PICO
|
||||
IOMUX->SECCFG.PINCM[TFT_RST_INDEX] = 0x00000081; // GPIO output, LCD !RST
|
||||
IOMUX->SECCFG.PINCM[TFT_DC_INDEX] = 0x00000081; // GPIO output, LCD D/C RS
|
||||
// IOMUX->SECCFG.PINCM[PB15INDEX] = 0x00000081; // GPIO output, LCD !RST
|
||||
// IOMUX->SECCFG.PINCM[PB16INDEX] = 0x00000081; // GPIO output, LCD RS
|
||||
// ** IOMUX->SECCFG.PINCM[PA13INDEX] = 0x00000081; // GPIO output, LCD RS
|
||||
IOMUX->SECCFG.PINCM[PB7INDEX] = 0x00040083; // SPI1 POCI
|
||||
IOMUX->SECCFG.PINCM[TFT_CS_INDEX] = 0x00000081; // PB6 is regular GPIO
|
||||
// IOMUX->SECCFG.PINCM[PB6INDEX] = 0x00000081; // PB6 is regular GPIO
|
||||
Clock_Delay(24); // time for gpio to power up
|
||||
TFT_DC->DOE31_0 |= TFT_DC_PIN; // PB16 is LCD RS
|
||||
// GPIOB->DOE31_0 |= 1<<16; // PB16 is LCD RS
|
||||
// ** GPIOA->DOE31_0 |= 1<<13; // PA13 is LCD RS
|
||||
TFT_RST->DOE31_0 |= TFT_RST_PIN;
|
||||
//GPIOB->DOE31_0 |= 1<<15; // PB15 is LCD !RST
|
||||
// GPIOB->DOUTSET31_0 = 1<<16; // RS=1
|
||||
TFT_DC_HIGH();
|
||||
// ** GPIOA->DOUTSET31_0 = 1<<13; // RS=1
|
||||
// GPIOB->DOUTSET31_0 = 1<<15; // !RST = 1
|
||||
TFT_RST_HIGH();
|
||||
TFT_CS->DOE31_0 |= TFT_CS_PIN; // PB6 is regular GPIO
|
||||
//GPIOB->DOE31_0 |= 1<<6; // PB6 is regular GPIO
|
||||
SPI1->CLKSEL = 8; // SYSCLK
|
||||
// bit 3 SYSCLK
|
||||
// bit 2 MFCLK
|
||||
// bit 1 LFCLK
|
||||
SPI1->CLKDIV = 0; // divide by 1
|
||||
// bits 2-0 n (0 to 7), divide by n+1
|
||||
//Set the bit rate clock divider to generate the serial output clock
|
||||
// outputBitRate = (spiInputClock) / ((1 + SCR) * 2)
|
||||
// 8,000,000 = (16,000,000)/((0 + 1) * 2)
|
||||
// 8,000,000 = (32,000,000)/((1 + 1) * 2)
|
||||
// 6,666,667 = (40,000,000)/((2 + 1) * 2)
|
||||
// 10,000,000 = (40,000,000)/((1 + 1) * 2)
|
||||
// 8,000,000 = (80,000,000)/((4 + 1) * 2)
|
||||
// 8,000,000 = (Clock_Freq)/((m + 1) * 2)
|
||||
// m = (Clock_Freq/16000000) - 1
|
||||
if(busfreq <= 16000000){
|
||||
SPI1->CLKCTL = 0; // frequency= busfreq/2
|
||||
}else if(busfreq == 40000000){
|
||||
SPI1->CLKCTL = 1; // frequency= 10MHz
|
||||
// SPI1->CLKCTL = 2; // frequency= 6.66MHz
|
||||
}else{
|
||||
SPI1->CLKCTL = busfreq/16000000 -1; // 8 MHz
|
||||
}
|
||||
SPI1->CTL0 = 0x0007;
|
||||
// bit 14 CSCLR=0 not cleared
|
||||
// bits 13-12 CSSEL=0 CS0
|
||||
// bit 9 SPH = 0
|
||||
// bit 8 SPO = 0
|
||||
// bits 6-5 FRF = 00 (3 wire)
|
||||
// bits 4-0 n=7, data size is n+1 (8bit data)
|
||||
SPI1->CTL1 = 0x0015;
|
||||
// bits 29-24 RXTIMEOUT=0
|
||||
// bits 23-16 REPEATX=0 disabled
|
||||
// bits 15-12 CDMODE=0 manual
|
||||
// bit 11 CDENABLE=0 CS3
|
||||
// bit 7-5 =0 no parity
|
||||
// bit 4=1 MSB first
|
||||
// bit 3=0 POD (not used, not peripheral)
|
||||
// bit 2=1 CP controller mode
|
||||
// bit 1=0 LBM disable loop back
|
||||
// bit 0=1 enable SPI
|
||||
TFT_CS_HIGH(); // disable LCD
|
||||
if(LCDresetFlag) return;
|
||||
LCDresetFlag = 1;
|
||||
SPI1_Reset();
|
||||
|
||||
|
||||
}
|
||||
|
||||
// SDC CS initialization
|
||||
void CS_Init(void){
|
||||
IOMUX->SECCFG.PINCM[SDC_CS_INDEX] = (uint32_t) 0x00000081;
|
||||
// IOMUX->SECCFG.PINCM[PB0INDEX] = (uint32_t) 0x00000081;
|
||||
// ** IOMUX->SECCFG.PINCM[PA12INDEX] = (uint32_t) 0x00000081;
|
||||
SDC_CS->DOE31_0 |= SDC_CS_PIN;
|
||||
SDC_CS_HIGH(); // PB0=1
|
||||
}
|
||||
|
||||
/* STAT register
|
||||
* 4 BUSY 0h = SPI is in idle mode. 1h = SPI is currently transmitting and/or receiving data, or transmit FIFO is not empty.
|
||||
3 RNF Receive FIFO not full 0h = Receive FIFO is full. 1h = Receive FIFO is not full.
|
||||
2 RFE Receive FIFO empty. 0h = Receive FIFO is not empty. 1h = Receive FIFO is empty.
|
||||
1 TNF Transmit FIFO not full 0h = Transmit FIFO is full. 1h = Transmit FIFO is not full.
|
||||
0 TFE Transmit FIFO empty. 0h = Transmit FIFO is not empty. 1h = Transmit FIFO is empty.*/
|
||||
|
||||
//---------TFT_OutData------------
|
||||
// Output 8-bit data to SPI port
|
||||
// Input: data is an 8-bit data to be transferred
|
||||
// Output: none
|
||||
void TFT_OutData(char data){char response;
|
||||
// while((SPI1->STAT&0x02) == 0x00){}; // spin if TxFifo full
|
||||
while((SPI1->STAT&0x10) == 0x10){}; // spin if SPI busy
|
||||
SDC_CS_HIGH(); // PB0 high
|
||||
TFT_CS_LOW(); // PB6 low
|
||||
// GPIOB->DOUTSET31_0 = 1<<16; // RS=PB16=1 for data
|
||||
TFT_DC_HIGH(); // RS=PB16=1 for data
|
||||
// ** GPIOA->DOUTSET31_0 = 1<<13; // RS=PA13=1 for data
|
||||
SPI1->TXDATA = data;
|
||||
while((SPI1->STAT&0x04) == 0x04){}; // spin SPI RxFifo empty
|
||||
response = SPI1->RXDATA; // has no meaning, flush
|
||||
TFT_CS_HIGH(); // PB6 high
|
||||
}
|
||||
//---------TFT_OutCommand------------
|
||||
// Output 8-bit command to SPI port
|
||||
// Input: data is an 8-bit data to be transferred
|
||||
// Output: none
|
||||
void TFT_OutCommand(char command){char response;
|
||||
while((SPI1->STAT&0x10) == 0x10){}; // spin if SPI busy
|
||||
SDC_CS_HIGH(); // PB0 high
|
||||
TFT_CS_LOW(); // PB6 low
|
||||
//GPIOB->DOUTCLR31_0 = 1<<16; // RS=PB16=0 for command
|
||||
TFT_DC_LOW(); // RS=PB16=0 for command
|
||||
// ** GPIOA->DOUTCLR31_0 = 1<<13; // RS=PA13=0 for command
|
||||
SPI1->TXDATA = command;
|
||||
while((SPI1->STAT&0x10) == 0x10){}; // spin if SPI busy
|
||||
response = SPI1->RXDATA; // has no meaning, flush
|
||||
TFT_CS_HIGH(); // PB6 high
|
||||
}
|
||||
Reference in New Issue
Block a user