add resetGPIO

sdkconfig.seeed_xiao_esp32c6

@@ -132,7 +132,6 @@ CONFIG_SOC_GPIO_DEEP_SLEEP_WAKE_VALID_GPIO_MASK=0
 CONFIG_SOC_GPIO_DEEP_SLEEP_WAKE_SUPPORTED_PIN_CNT=8
 CONFIG_SOC_GPIO_VALID_DIGITAL_IO_PAD_MASK=0x000000007FFFFF00
 CONFIG_SOC_GPIO_SUPPORT_FORCE_HOLD=y
-CONFIG_SOC_GPIO_SUPPORT_HOLD_IO_IN_DSLP=y
 CONFIG_SOC_GPIO_SUPPORT_HOLD_SINGLE_IO_IN_DSLP=y
 CONFIG_SOC_GPIO_CLOCKOUT_BY_GPIO_MATRIX=y
 CONFIG_SOC_CLOCKOUT_HAS_SOURCE_GATE=y
@@ -2344,13 +2343,6 @@ CONFIG_LIBC_TIME_SYSCALL_USE_RTC_HRT=y
 #
 # CONFIG_OPENTHREAD_ENABLED is not set
 
-#
-# Thread Console
-#
-CONFIG_OPENTHREAD_CLI=y
-CONFIG_OPENTHREAD_CONSOLE_COMMAND_PREFIX="ot"
-# end of Thread Console
-
 #
 # OpenThread Spinel
 #

src/BLE.cpp

@@ -6,6 +6,7 @@
 #include "defines.h"
 #include <mutex>
 #include "bmHTTP.hpp"
+#include "esp_mac.h"
 
 std::atomic<bool> flag_scan_requested{false};
 std::atomic<bool> credsGiven{false};
@@ -28,6 +29,7 @@ std::atomic<NimBLECharacteristic*> authConfirmChar = nullptr;
 std::atomic<NimBLECharacteristic*> credsChar = nullptr;
 std::atomic<NimBLECharacteristic*> tokenChar = nullptr;
 std::atomic<NimBLECharacteristic*> ssidRefreshChar = nullptr;
+std::atomic<NimBLECharacteristic*> deviceInfoChar = nullptr;
 
 NimBLEAdvertising* initBLE() {
   finalAuth = false;
@@ -93,6 +95,27 @@ NimBLEAdvertising* initBLE() {
                         );
   connectConfirmChar.load()->createDescriptor("2902"); // Add BLE2902 descriptor for notifications
 
+  // 0x0006 - Device Info (READ) - MAC address and other device details
+  deviceInfoChar = pService->createCharacteristic(
+                          "0006",
+                          NIMBLE_PROPERTY::READ
+                        );
+  // Build device info JSON with MAC address
+  uint8_t mac[6];
+  esp_read_mac(mac, ESP_MAC_WIFI_STA);
+  char macStr[18];
+  snprintf(macStr, sizeof(macStr), "%02X:%02X:%02X:%02X:%02X:%02X", 
+           mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
+  
+  cJSON *infoRoot = cJSON_CreateObject();
+  cJSON_AddStringToObject(infoRoot, "mac", macStr);
+  cJSON_AddStringToObject(infoRoot, "firmware", "1.0.0");
+  cJSON_AddStringToObject(infoRoot, "model", "BlindMaster-C6");
+  char *infoJson = cJSON_PrintUnformatted(infoRoot);
+  deviceInfoChar.load()->setValue(std::string(infoJson));
+  cJSON_Delete(infoRoot);
+  free(infoJson);
+
   // Start
   pService->start();
   

src/CMakeLists.txt

@@ -1,7 +1,7 @@
 # This file was automatically generated for projects
 # without default 'CMakeLists.txt' file.
 
-FILE(GLOB_RECURSE app_sources ${CMAKE_SOURCE_DIR}/src/*.* ${CMAKE_SOURCE_DIR}/include/*.cpp)
+FILE(GLOB_RECURSE app_sources ${CMAKE_SOURCE_DIR}/src/*.*)
 
 idf_component_register(SRCS ${app_sources}
                     INCLUDE_DIRS "."

src/main.cpp

@@ -18,6 +18,17 @@ Encoder* bottomEnc = new Encoder(InputEnc_PIN_A, InputEnc_PIN_B);
 // Global calibration instance
 Calibration calib;
 
+void switchOnOffServo() {
+  while (1) {
+    printf("Servo On\n");
+    servoOn(CCW, manual);
+    vTaskDelay(pdMS_TO_TICKS(2000));
+    printf("Servo Off\n");
+    servoOff();
+    vTaskDelay(pdMS_TO_TICKS(2000));
+  }
+}
+
 void mainApp() {
   esp_err_t ret = nvs_flash_init(); // change to secure init logic soon!!
   // 2. If NVS is full or corrupt (common after flashing new code), erase and retry
@@ -35,6 +46,8 @@ void mainApp() {
   bottomEnc->init();
   servoInit();
 
+  // switchOnOffServo();
+
   setupLoop();
   
   statusResolved = false;

src/servo.cpp

@@ -38,6 +38,7 @@ void servoInit() {
   ESP_ERROR_CHECK(ledc_channel_config(&ledc_channel));
 
   // Configure servo power switch pin as output
+  gpio_reset_pin(servoSwitch);
   gpio_set_direction(servoSwitch, GPIO_MODE_OUTPUT);
   gpio_set_level(servoSwitch, 0); // Start with servo power off